Myalarm Genesys 824 Alpha Dokumentacja Pobierz pdf (Strona 3)

3440-0241 Rev G

7 - FIRE ZONES

are used for devices such as smoke

detectors (4 wire), heat sensor, water flow, etc. that

need to be active 24 hours.

8 - DAY CIRCUIT

is used for devices such as window

foil, screens, etc. In a disarmed state, an activation

creates a trouble (trbl) condition and will report a

trouble code if programmed. In an armed state, an

activation will create an alarm condition.

ARMING MODE ENTRY/EXIT 1

and 2

PERIMETER

INSTANT

INTERIOR #1 INTERIOR #2 INTERIOR #3

AWAY Delayed Exit

Delayed Entry

Delayed Exit

Instant

Delayed Exit

Follower or

Instant

Delayed Exit

Follower or

Instant

Delayed

STAY Delayed Exit

Delayed Entry

Delayed Exit

Instant

Delayed Exit

Follower or

Instant

Bypassed Delayed

INSTANT Instant Always Instant Always Instant Always Bypassed Delayed

LOOP TYPE

is the second digit entry. The loop type

and value entered are:

0 - Normally Open

1 - Normally Closed

* 2 - Normally Open - Normally Closed

* 3 - N.O. - supervised w/EOL - reports trouble on

break, alarm on short

* 4 - N.C. - supervised w/EOL - reports trouble on

short, alarm on open

NOTE:

EOL resistor 2.2k ohm 1/2 watt

(Optex Part Number: 1401-4649).

ITEM A - Loop Response

- Adjusted in two digit

increments in a multiplier of 50 ms. A longer loop

response may be required for devices such as water

flow detectors. A shorter loop response may be

required for devices such as glass break detectors.

Value: 00 - 99 x 50 ms.,

Default: 05 (250 ms.)

ITEM B - Alarm Code

- (2 Digit Entry)

The panel will transmit this code when the zone

creates an alarm condition.

Value: 01 - FF,

Default: 00 (Disabled

ITEM C - Trouble Code

- (2 Digit Entry)

This code that will be transmitted when a zone that is

programmed for a Loop Type three or four creates a

trouble condition.

Value: 01 - FF,

Default: 00 (Disabled)

ITEM D - Bypass Code

- (2 Digit Entry)

This code will be transmitted when the zone is

bypassed and the system is armed if the zone is

programmed for bypass allowed (see Item G)

Value: 01 - FF,

Default: 00 (Disabled).

NOTE

BYPASS SHOULD NOT BE ALLOWED

ON FIRE CIRCUITS.

ITEM E - Restore Code

(2 Digit Entry)

This restore code is a common function that is

transmitted either after an alarm condition or after a

trouble (trbl) condition if programmed as loop type

three or four.

Value: 01 - FF,

Default: 00 (Disabled)

ITEM F -Zone Features

(MultipleEntries) Depressing

the number that corresponds to the option that you

wish to enable and it will also be displayed on the

LCD. Depressing a number that previously was

displayed will remove the number from the LCD and

disable the option.

(

Shows Default condition

)

OPTIONS

1 = Telephone Output

2 = Audible

3 = Pulse Bell

4 = PGM 1

5 = PGM 2

6 = Walk Test

7 = Monitor

8 = Silent Day - Audible Armed

1 - TELEPHONE OUTPUT

- is required to be enabled to

transmit all zone reporting codes. If the codes are

programmed and this function is not active, the zone report

codes will not transmit.

Default: YES

2 - AUDIBLE

- must be enabled to energize the steady bell

voltage output If this function is not enabled the zone will

be silent. (See Item 58 for cutoff times.)

Default: YES

Note:

For Temporal Pattern Set Audible to Yes

3 - PULSE BELL

- is required to be enabled to energize

the pulsing bell voltage output. Audible must also be

enabled to energize this function.

Default: NO

Note:

For Temporal Pattern Set Pulse Bell to Yes

4 - PGM OUTPUT 1

- is an open collector that sinks to

ground for the amount of time that is programmed under

1 2 3 4 5 6 7 8 ... 21 22

Komentarze do niniejszej Instrukcji

Brak uwag

Myalarm Genesys 824 Alpha Dokumentacja Strona 3

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Myalarm Genesys 824 Alpha